Back to blogs

Anti-Static and ESD-Safe Disposable Garments, Explained

Date

September 5, 2026

Author

Sandeep Bapna

Table of Contents
Quick Inquiry Form
Anti-static and ESD-safe garments

Key Takeaways

  • Anti-static and ESD-safe are not synonyms. Anti-static treatment reduces how readily a fabric generates and holds charge. An ESD-safe garment is a component of a formal static control programme built to a standard such as ANSI/ESD S20.20-2021 or its technically equivalent international counterpart, IEC 61340-5-1:2024.
  • Humidity changes the problem more than most buyers expect. The EOS/ESD Association records a person walking across a carpeted floor generating about 35,000 V at 10 to 25% relative humidity and about 1,500 V at 65 to 90%, and notes that charge generation still occurs at high humidity.
  • The damage threshold is far lower than the charge available. The same reference notes components that fail below 100 V, and disk drive components sensitive below 10 V, against a worker at a bench who can carry 6,000 V in dry conditions.
  • ESD control is a system, not a garment. IEC 61340-5-1:2024 applies to operations handling parts with withstand voltages of 100 V HBM or greater, and sets requirements for a whole control programme, not for a single item of clothing.
  • Specify the category, not the adjective. The word “anti-static” on a quotation, unqualified by a test method and test conditions, tells a procurement team almost nothing about what it is buying.

Anti-static and ESD-safe are two different specifications, and treating them as one is the most expensive mistake in this category. Anti-static treatment reduces a fabric’s tendency to generate and retain electrostatic charge. An ESD-safe garment is something else: a garment built with conductive elements, verified by a defined test method, and worn as one part of a grounded static control system that also covers footwear, flooring, work surfaces, wrist straps and packaging.

The confusion is not the buyer’s fault. Product listings, marketplace buyer’s guides and a good deal of supplier content use the two phrases interchangeably, so a procurement team asked to source “anti-static garments” often cannot tell whether the requirement is a single-use treated disposable garment or a launderable smock with a conductive fibre grid qualified into an ESD control programme. Both errors are common. Facilities buy full ESD garments where anti-static treatment would have met the actual requirement, and facilities buy anti-static disposables believing they satisfy an ESD programme that they do not.

This guide sets out what each term means, how static performance is assessed, how anti-static behaviour changes with humidity and over the life of a garment, and how to write the requirement into a specification so that quotations become comparable. Dispowear Protection manufactures over 3 million disposable garments every month from its own GenFab® virgin-polypropylene nonwoven fabric, with 20+ years of manufacturing experience and anti-static treatment available as a standard customisation across the range, serving customers across India and international markets.

What anti-static treatment actually does

Anti-static treatment reduces the rate at which a fabric generates charge through contact and separation, and helps the charge that does form bleed away across the surface rather than accumulate in one place. It is applied either as a topical finish or incorporated into the fabric during manufacture. What it does not do is turn the garment into a conductive path to earth.

Polypropylene and the other synthetics used in disposable protective clothing generate charge readily because they are excellent insulators. Charge is created whenever two dissimilar surfaces touch and separate, which in a garment happens continuously: sleeve against torso, garment against chair, operator against doorway. Because the fabric is insulative, that charge stays where it was created instead of spreading out and draining away. On an untreated nonwoven you can feel the result as cling, and see it as dust and fibre clinging to a coverall that was clean when it left the pack.

That is precisely what anti-static treatment is good at solving. In a controlled environment it delivers three practical benefits: less particle attraction to the garment surface, so the coverall stops acting as a collector and later re-emitter of particulate; fewer nuisance discharges, the small shocks that make operators flinch and touch surfaces they should not; and less cling, which matters more than it sounds because a garment that clings is a garment that is adjusted, and every adjustment inside a controlled area is a handling event.

Be precise about the scope of the claim. Anti-static treatment changes charge behaviour at the fabric surface. It does not create a designed, measured, continuous conductive path from the operator’s body through the garment to a grounded point, and it should never be described as though it does. For the fabric side of that distinction, our comparison of SBPP, SMS and PE laminate nonwovens sets out how the base fabrics differ before any treatment is applied.

What makes a garment ESD-safe

ESD-control garments are typically engineered with conductive or dissipative elements, such as conductive fibres or grid constructions, and are evaluated using the applicable garment test method. They are then specified as one part of a grounded system. The construction is the point. The conductive element is what allows charge on the outer surface of the garment to be conducted away rather than merely dispersed a little more evenly.

Two standards define the programme these garments belong to. ANSI/ESD S20.20-2021, published by the EOS/ESD Association, provides the administrative and technical requirements for establishing, implementing and maintaining an ESD control programme. IEC 61340-5-1:2024 is technically equivalent and applies to operations handling parts, assemblies and equipment with withstand voltages of 100 V human body model or greater, 200 V charged device model or greater, and 35 V for isolated conductors. Notice what both documents are: programme standards. Neither is a garment specification, and neither can be satisfied by a purchase order.

Verification is handled separately. ANSI/ESD STM2.1-2018 is the test method for the resistive characterisation of garments containing surface conductive or dissipative components, and the international equivalent is IEC 61340-4-9. A separate European standard, EN 1149-5:2018, covers electrostatic dissipative protective clothing for a different purpose again: avoiding incendiary discharge in explosive atmospheres where the minimum ignition energy is not less than 0.016 mJ. EN 1149-5 is about ignition risk to people, not damage to components, and it explicitly excludes separate gloves and footwear. Three standards, three different jobs, and a specification that names none of them is not a specification.

There is also a construction reality that buyers should hear plainly from a manufacturer. Garments built around a durable conductive grid are typically launderable rather than single-use, because the grid is an engineered, verified feature that a facility expects to hold across many wears under a controlled laundering contract. That is a genuine constraint on what a disposable garment can be, and it is discussed honestly further down this page.

CriterionAnti-static treated garmentESD-safe (static control) garment
What it isFabric treated so that it generates and retains less chargeGarment constructed with conductive or dissipative elements, commonly a carbon fibre grid
Primary purposeReduce particle attraction, cling and nuisance dischargeControl charge on personnel within a defined ESD protected area
Governing documentUsually a supplier specification and an agreed test methodA formal control programme under ANSI/ESD S20.20 or IEC 61340-5-1
How it is verifiedFabric-level testing to the method and conditions named on the datasheetGarment resistive characterisation, for example ANSI/ESD STM2.1 or IEC 61340-4-9
Depends on groundingNo, it works at the fabric surfaceYes, the garment is one link in a path to earth
Typical formatSingle-use disposable coverall, lab coat, cap, sleeve or shoe coverLaunderable smock, coat or coverall under a controlled laundering contract
Typical environmentPharmaceutical and food cleanrooms, laboratories, paint and coating areas, general assemblyElectronics assembly, semiconductor, PCB and sensitive component handling
Common failureBought against an ESD requirement it was never designed to meetBought into a facility with no grounding, flooring or footwear system to complete the path

Standards positions as published by the EOS/ESD Association and BSI for EN 1149-5:2018. For the footwear side of the same question, see our guide to anti-static and conductive shoe covers.

How much charge is actually available

The reason this distinction matters is arithmetic. The charge routinely generated by ordinary human activity is orders of magnitude larger than the charge that damages a modern component, and the gap widens sharply as the air gets drier.

The EOS/ESD Association’s published fundamentals set out typical electrostatic voltages for common activities at two humidity bands. A person walking across a carpeted floor generates about 35,000 V at 10 to 25% relative humidity and about 1,500 V at 65 to 90%. Picking up a polythene bag from a bench generates about 20,000 V dry and 1,200 V humid. A worker simply seated at a bench carries about 6,000 V dry and 100 V humid. Against those figures, the association notes components that fail below 100 V and disk drive components that can be damaged below 10 V.

Typical electrostatic voltages generated by common activities Same activity, two humidity bands. Bars scaled to 35,000 V. 10 to 25% relative humidity 65 to 90% relative humidity Walking across carpet 35,000 V 1,500 V Polythene bag lifted from bench 20,000 V 1,200 V Urethane foam work chair 18,000 V 1,500 V Walking across vinyl tile 12,000 V 250 V Worker seated at a bench 6,000 V 100 V Some components fail below 100 V. Disk drive components can be damaged below 10 V. Source: EOS/ESD Association, Fundamentals of Electrostatic Discharge, Part 1.
Dry air multiplies the charge available by more than twenty times for the same activity, which is why a static claim without its test humidity is not a claim at all.

Two conclusions follow. First, ambient conditions are part of the specification, not background noise. A garment tested at 50% relative humidity and deployed in an air-conditioned Indian electronics plant running at 25% will not behave the way the datasheet suggests. Second, humidity control is not a substitute for static control. The association is explicit that charge generation still occurs at high relative humidity, and 1,500 V is still fifteen times the level at which some components fail.

ESD control is a system, not a garment

This is the part that suppliers rarely say, so we will say it. A compliant garment in a facility with no personnel grounding, no ESD footwear, no dissipative flooring and no controlled work surfaces achieves very little. The garment is one link in a chain whose purpose is to give charge a defined route to earth. Remove any other link and the chain does not reach ground, and the garment becomes an expensive item of clothing.

The garment is one link in the path to ground Illustrative schematic of an ESD control programme, not to scale Operator charge source Garment what you buy Footwear or wrist strap Flooring dissipative Earth ground point Break any single link and the path stops. The garment then controls nothing. The programme standard governs every box. The purchase order governs one of them. Anti-static treatment acts on the garment surface only and does not join the chain. Work surfaces, ionisation and ESD packaging sit alongside this path in a full programme. Structure per ANSI/ESD S20.20 and IEC 61340-5-1 programme requirements.
Buying the garment is the easy part of an ESD programme, and on its own it is the least effective part.

If your facility has an ESD control programme, the programme document specifies the garment, the footwear, the flooring and the verification schedule, and your job in procurement is to source against that document rather than against a category name. If your facility does not have one, buying an ESD garment does not create one, and the money is better spent on the compliance verification plan first.

So which one does your facility actually need?

The requirement comes from your static control programme if you have one, and from what is genuinely at risk in the process if you do not. Working through it takes about five minutes and saves a great deal of money in both directions.

  • Are static-sensitive components handled unprotected? Bare printed circuit boards, integrated circuits, MEMS devices, sensors, laser diodes and hard disk components are the trigger. If the answer is yes, you are in ESD programme territory and the programme, not the catalogue, defines the garment.
  • Is there a documented ESD control programme? If a programme exists under ANSI/ESD S20.20 or IEC 61340-5-1, read it. It will already name the garment class, the test method and the verification interval. Source against those words exactly.
  • Is the concern particulate rather than component damage? Pharmaceutical, medical device, food and laboratory cleanrooms usually fall here. The static problem is that charged garments attract and hold particles and later shed them. Anti-static treatment addresses that directly, and a full ESD garment adds cost without adding relevant benefit.
  • Is there a flammable atmosphere? That is a third and separate question, governed by EN 1149-5 and by your hazardous area classification rather than by either of the categories above. Our guide on choosing chemical protective clothing by hazard type covers how that assessment fits alongside the rest of the PPE decision.
  • Are you unsure? The right response is to ask whether static-sensitive components are handled, not to buy the higher specification by default. Over-specifying an ESD garment for a pharmaceutical cleanroom is a recurring and avoidable cost on a daily-consumption line.

For most pharmaceutical, biotech, food and laboratory operations in India, the honest answer is that anti-static treated disposable coveralls and gowning consumables meet the requirement, and that a formal ESD programme is not in scope. For electronics assembly, semiconductor and precision manufacturing, the answer is the opposite, and it is the programme document that decides.

How static performance is assessed

Static performance is assessed by measuring a material’s or a garment’s electrical characteristics under controlled conditions, and the relevant measurement depends on which category of product is being verified. For static control garments, ANSI/ESD STM2.1 and its international equivalent IEC 61340-4-9 define resistive characterisation, including sleeve-to-sleeve and point-to-point measurements on the assembled garment rather than on a swatch of fabric. For dissipative protective clothing under EN 1149-5, the material requirements rest on surface resistivity, electrical resistance and charge decay.

Three practical points follow for anyone reading a datasheet.

  1. A result without its conditions is not a result. Temperature and relative humidity change the measurement materially, as the voltage figures above show. Any performance claim should name the test method, the temperature and the relative humidity at which it was obtained.
  2. Fabric-level and garment-level testing are different things. A fabric can behave one way and the finished garment another, because seams, closures, zips and non-dissipative attachments all affect the assembled article. Garment standards test the garment for exactly this reason.
  3. The word on its own means nothing. “Anti-static” printed on a product sheet with no method, no conditions and no measured property is marketing, not specification. This is the single most useful thing a procurement team can learn from this page.

Our overview of ISO, EN and BIS standards for disposable protective clothing sets out how to read the wider standards landscape that these documents sit inside.

Does anti-static performance last?

Anti-static performance is not a fixed property of a garment for its whole life. It varies with ambient humidity, with handling, with abrasion, and above all with what happens between wears. This is where single-use and reusable products diverge sharply, and it is the area a manufacturer can speak to most usefully.

Humidity is the largest day-to-day variable. The same treated garment behaves differently in a Chennai monsoon and in a dry, heavily air-conditioned assembly hall in February. Facilities that monitor and control relative humidity in the working range recommended for their process remove most of that variance, and facilities that do not should expect seasonal drift in how their garments behave.

Handling and abrasion matter for topical finishes. A treatment applied at the fabric surface is subject to wear at friction points: cuffs, knees, seat, the inside of the elbow. In a single-use garment this rarely becomes significant, because the exposure window is one shift.

Laundering is the classic failure point for reusable ESD garments. A conductive grid garment is only as good as its last wash, and its resistive characteristics are expected to be verified on a defined schedule under a controlled laundering contract. That is a real, ongoing programme cost and a real, ongoing risk, and it is one of the least discussed parts of ESD control. Our comparison of disposable and reusable protective clothing covers the total-cost picture in more depth.

Single use has one structural advantage here. A disposable garment’s treated performance only has to hold for one wear, from pack to disposal, so the variable that destroys consistency in reusable garments is removed entirely. That advantage is only real if the treatment is applied consistently from batch to batch, which in turn depends on whether the supplier controls the fabric. Dispowear makes its own virgin-polypropylene SBPP nonwoven fabric under the GenFab® brand, so anti-static treatment is applied in-house on our own line rather than specified to a fabric trader and hoped for. For the footwear element of the same gowning kit, we manufacture anti-static and conductive shoe covers as a separate product line.

An honest note: if your facility runs a formal ESD control programme and handles bare, static-sensitive components, a launderable garment built around a verified conductive grid is the correct product and a treated disposable is not a substitute for it. We manufacture disposables, and we would rather tell you that than sell you the wrong category. The place where disposables genuinely win is the much larger set of environments where the risk is particle attraction, cling and nuisance discharge rather than component damage, and where changeover discipline, contamination control and per-wear consistency matter more than a designed path to earth. Work out which of those two rooms you are standing in before you compare quotations, because the two products are not competing with each other.

Why source anti-static disposable protective clothing from Dispowear Protection

  • Audit-ready documentation. Certificates of analysis, GSM data, fabric test reports and lot traceability with every batch, manufactured at FDA-registered facility under a certified quality management system for applicable products and regulated manufacturing processes, so your QA team can qualify the supplier and defend the choice in front of an auditor.
  • Supply reliability at scale. Over 3 million garments and 650 tonnes of fabric a month across two plants in Rajasthan and Gujarat, with 900+ staff and 20+ years of manufacturing experience, so a daily-consumption line never runs short mid-programme.
  • Backward integration and customisation. We manufacture our own virgin-polypropylene SBPP nonwoven under the GenFab® brand, which is what lets us apply anti-static treatment selected according to application requirements consistently from batch to batch, and control GSM, lamination, colour, sizing and white-label or full OEM production rather than sell from a fixed catalogue.
  • Made in India. Import substitution against overseas supply, INR pricing and local lead times, serving customers across India and international markets, so a change in specification does not mean waiting a quarter for the next container.

GenFab® anti-static garment specification

The parameters below are the ones worth naming on a purchase order. Anything left unspecified will be decided by the supplier, and it will be decided the cheapest way.

ParameterTypical specification
FabricGenFab® virgin-polypropylene SBPP nonwoven, manufactured in-house; SMS and PE laminate constructions also available
GSMSelected according to application requirements and confirmed on the order datasheet
Anti-static treatmentAnti-static treatment selected according to application requirements; performance confirmed through technical documentation where applicable
FormatsCoveralls, lab coats, gowns, bouffant caps, hoods, sleeve covers, aprons and shoe covers, so a full gowning kit is specified on one order
Conductive footwearConductive and anti-static shoe cover range available as a separate line, specified to application requirements
SizesStandard size range across formats; custom sizing to customer requirement
ColourWhite, blue, green and custom shades for colour coding by area, zone or shift
SterilityNon-sterile as standard; sterile options and sterility assurance confirmed through technical documentation where applicable
BrandingCustom printing, private label and OEM packaging available
PackagingPoly-bagged in cleanroom-compatible packs, carton quantity to customer requirement
DocumentationCOA, GSM data, fabric test reports and lot traceability supplied with each batch

Figures are indicative and confirmed on the product datasheet for each order. Anti-static treatment is selected according to application requirements, and performance is confirmed through technical documentation where applicable.

Writing it into a specification

This is the section to lift into your tender document. Six lines, and they make quotations comparable for the first time.

  1. State the category. Say “anti-static treated” or “ESD-specified static control garment”. Do not write “anti-static” and expect the supplier to guess which one you mean.
  2. Name the programme standard, if there is one. If your facility works to ANSI/ESD S20.20 or IEC 61340-5-1, cite it and cite the internal programme document number alongside it.
  3. Name the test method and the conditions. Any performance claim should be tied to a named method with the temperature and relative humidity at which it was measured, at fabric level or garment level as appropriate.
  4. State whether the garment forms part of a grounded system. If it does, say what the rest of the system is: footwear, flooring, wrist straps, work surfaces. If it does not, say so, and the supplier will stop quoting the wrong product.
  5. State single-use or reusable, and the changeover rule. One wear per garment, or a defined laundering and reverification cycle. This is a cost driver and a compliance driver at the same time.
  6. Ask for the documentation with the delivery. COA, GSM data, fabric test reports and lot traceability against the batch you received, not a generic certificate issued once at qualification.

A specification written this way does two useful things at once. It makes competing quotations genuinely comparable, and it forces an internal conversation about whether the facility actually has the static control programme its purchase orders imply.

The bottom line

Anti-static and ESD-safe describe two different products solving two different problems, and the cost of confusing them runs in both directions. Anti-static treatment reduces charge generation and retention at the fabric surface, which is the right answer wherever the risk is particle attraction, cling and nuisance discharge. An ESD-safe garment is a verified link in a grounded system, which is the right answer only where static-sensitive components are handled and a control programme under ANSI/ESD S20.20 or IEC 61340-5-1 actually exists to govern it. Neither is a better version of the other. Decide which room you are in, write the category, the test method and the test conditions into the specification, and the quotations in front of you become comparable for the first time. A great many Indian facilities are having this conversation for the first time. It is worth having it properly.

Need anti-static treated coveralls, lab coats, hoods or shoe covers at a specified GSM, colour or format? Talk to our technical team to discuss anti-static customisation for your garment requirement, request samples and technical documentation, and get a bulk quotation built around your actual specification.

Frequently Asked Questions

Is anti-static the same as ESD-safe?

No. Anti-static treatment reduces how readily a fabric generates and retains electrostatic charge, working at the surface of the material. An ESD-control garment is typically engineered with conductive or dissipative elements, verified by a garment-level test method such as ANSI/ESD STM2.1, and used as one component of a grounded control programme under ANSI/ESD S20.20 or IEC 61340-5-1. Anti-static treatment is useful in many environments, but it does not by itself make a garment part of an ESD control programme.

Are disposable coveralls anti-static?

Only if they have been treated and the treatment is stated on the specification. Untreated polypropylene nonwoven is an insulator and generates charge readily through ordinary contact and separation, which is why cling and dust pick-up are common complaints on untreated coveralls. Anti-static treatment is a customisation, not a default property, so ask for it explicitly on the purchase order and ask what test method and conditions support the claim.

Do I need ESD garments for a pharmaceutical cleanroom?

Usually not. In pharmaceutical, biotech, medical device and food cleanrooms the static concern is normally particle attraction and nuisance discharge rather than damage to static-sensitive electronic components, and anti-static treated disposable cleanroom apparel addresses that. A formal ESD control programme applies where bare static-sensitive components are handled. If your site does both, for example a medical device plant with an electronics assembly area, the two areas will have different garment requirements and should be specified separately.

Does humidity affect anti-static performance?

Substantially. The EOS/ESD Association records the same activity, walking across a carpeted floor, generating about 35,000 V at 10 to 25% relative humidity and about 1,500 V at 65 to 90%. Dry, heavily air-conditioned production areas therefore present a much larger static problem than the same room in a humid season. Humidity control reduces the problem but does not remove it, because charge generation continues at high humidity, and it is not a substitute for a control programme where one is required.

Can a disposable garment be part of an ESD control programme?

Only where the programme document says it can, and that is a decision for the ESD programme owner rather than for a supplier. Garments intended to form a verified path to ground are typically launderable, because the conductive grid is expected to be reverified on a schedule across many wears. Where a programme uses disposables, it is usually for secondary coverage, for visitors, or in combination with other grounded elements. The practical answer for a procurement team is to source against the programme document rather than against a product description.

Sandeep Bapna

Sandeep Bapna is a commerce graduate. In 1993, he received an MBA with a finance concentration from Mumbai’s Narsee Monjee Institute of Management Studies, following his B.Com. (Hons). Following that, he began working for his father’s company, Mewar Polytex Ltd. He has played a vital role in developing the group’s business from Rs. 3 crores in 1993 to Rs. 650 crores in 2022. He was instrumental in the formation of Anita Plastics, Inc., a distribution company in the United States. He led the team that established Harmony Plastics P. Ltd. in 2005 to produce construction fabrics in collaboration with Alpha ProTech of the United States. He has also served in a leadership role on Rajasthan’s Plastics Export Committee. He serves as the Managing Director of Mewar Polytex Group.

Read More